Control panels

Mascontrol isa electronic pressure switch and protection device. They can be fitted to almost any pump with an outlet pressure of two bar minimum to ten bar maximum with a flow rate of between 40-200 litres per minute.The mascontrol will turn off in the case of no water to protect the pump from dry running. Suitable for most water systems from well, tank or low pressure mains.A solenoid must be installed if the pump being used has a high wattage/current rating.Mascontrol12 Volt0.18Kw Maximum20 Amp Maximum1" Male BSP Inlet/Outlet1.4Kg

Mascontrol is a electronic pressure switch and protection device. They can be fitted to almost any pump with an outlet pressure of two bar minimum to ten bar maximum with a flow rate of between 40-200 litres per minute.The mascontrol will turn off in the case of no water to protect the pump from dry running. Suitable for most water systems from well, tank or low pressure mains.A solenoid must be installed if the pump being used has a high wattage/current rating.Mascontrol24 Volt0.37Kw Maximum20 Amp Maximum1" Male BSP Inlet/Outlet1.4KgH 165mm x W 210mm x L 250mm

For connection with Borehole motor. On/off switch and resetable overload.

For connection with Borehole motor. On/off switch and resetable overload.

For connection with Borehole motor. On/off switch and resetable overload.

For connection with Borehole motor. On/off switch and resetable overload.

For connection with Borehole motor. On/off switch and resetable overload.

For connection with Borehole motor. On/off switch and resetable overload.

For connection with Borehole motor. On/off switch and resetable overload.

The 230v Presscontrol is a electronic pressure switch and protection device.Can be fitted to almost any pump with an outlet pressure of two bar minimum to ten bar maximum with a flow rate of between 40-200 litres per min. The presscontrol will turn off in the case of no water to protect the pump from dry running.Suitable for most water systems from well, tank or low pressure mains.Anotherversion called the controlpress is available for pumps with larger motors to be installed.Presscontrol230 Volt1.5Kw Maximum8 Amp Maximum1" Male BSP Inlet/Outlet1.4KgAutomatically turns on and off a pump

Single pump control panels - Delta 1 / Twin pump control panels - Delta 2Delta 1/10 Delta 2/10 7.5Kw 9-12.5 AmpsDelta 1/15 Delta 2/15 11Kw 11-16 AmpsDelta 1/20 Delta 2/20 15Kw 14-20 AmpsIP54 Steel enclosure with interlock main isolator. Line fuses and overload relays. Transformer for low voltage circuit, auto changeover relay (twin pump) run and trip indicators and hour counter, auto off manual switch. Alarm circuit 24v AC.Single pump panels require a two float operation (three if using the alarm feature).Twin pump panels require a three float operation (four if using the alarm feature).Optional Extra's - High Level Alarm Equipment –Rectifier AC-DC & Internal buzzer/Remote connection – Code 200-00112 Volt AC/DC 22mm Panel Sounder / Continuous lit lamp IP20 - Code 200-002Flashing Beacon Sounder 12/24v DC - Code 309-5922

Single pump control panels - Delta 1 / Twin pump control panels - Delta 2Delta 1/10 Delta 2/10 7.5Kw 9-12.5 AmpsDelta 1/15 Delta 2/15 11Kw 11-16 AmpsDelta 1/20 Delta 2/20 15Kw 14-20 AmpsIP54 Steel enclosure with interlock main isolator. Line fuses and overload relays. Transformer for low voltage circuit, auto changeover relay (twin pump) run and trip indicators and hour counter, auto off manual switch. Alarm circuit 24v AC.Single pump panels require a two float operation (three if using the alarm feature).Twin pump panels require a three float operation (four if using the alarm feature).Optional Extra's - High Level Alarm Equipment –Rectifier AC-DC & Internal buzzer/Remote connection – Code 200-00112 Volt AC/DC 22mm Panel Sounder / Continuous lit lamp IP20 - Code 200-002Flashing Beacon Sounder 12/24v DC - Code 309-5922

Single pump control panels - Delta 1 / Twin pump control panels - Delta 2Delta 1/10 Delta 2/10 7.5Kw 9-12.5 AmpsDelta 1/15 Delta 2/15 11Kw 11-16 AmpsDelta 1/20 Delta 2/20 15Kw 14-20 AmpsIP54 Steel enclosure with interlock main isolator. Line fuses and overload relays. Transformer for low voltage circuit, auto changeover relay (twin pump) run and trip indicators and hour counter, auto off manual switch. Alarm circuit 24v AC.Single pump panels require a two float operation (three if using the alarm feature).Twin pump panels require a three float operation (four if using the alarm feature).Optional Extra's - High Level Alarm Equipment –Rectifier AC-DC & Internal buzzer/Remote connection – Code 200-00112 Volt AC/DC 22mm Panel Sounder / Continuous lit lamp IP20 - Code 200-002Flashing Beacon Sounder 12/24v DC - Code 309-5922

Single pump control panels - Delta 1 / Twin pump control panels - Delta 2Delta 1/10 Delta 2/10 7.5Kw 9-12.5 AmpsDelta 1/15 Delta 2/15 11Kw 11-16 AmpsDelta 1/20 Delta 2/20 15Kw 14-20 AmpsIP54 Steel enclosure with interlock main isolator. Line fuses and overload relays. Transformer for low voltage circuit, auto changeover relay (twin pump) run and trip indicators and hour counter, auto off manual switch. Alarm circuit 24v AC.Single pump panels require a two float operation (three if using the alarm feature).Twin pump panels require a three float operation (four if using the alarm feature).Optional Extra's - High Level Alarm Equipment –Rectifier AC-DC & Internal buzzer/Remote connection – Code 200-00112 Volt AC/DC 22mm Panel Sounder / Continuous lit lamp IP20 - Code 200-002Flashing Beacon Sounder 12/24v DC - Code 309-5922

Single pump control panels - Delta 1 / Twin pump control panels - Delta 2Delta 1/10 Delta 2/10 7.5Kw 9-12.5 AmpsDelta 1/15 Delta 2/15 11Kw 11-16 AmpsDelta 1/20 Delta 2/20 15Kw 14-20 AmpsIP54 Steel enclosure with interlock main isolator. Line fuses and overload relays. Transformer for low voltage circuit, auto changeover relay (twin pump) run and trip indicators and hour counter, auto off manual switch. Alarm circuit 24v AC.Single pump panels require a two float operation (three if using the alarm feature).Twin pump panels require a three float operation (four if using the alarm feature).Optional Extra's - High Level Alarm Equipment –Rectifier AC-DC & Internal buzzer/Remote connection – Code 200-00112 Volt AC/DC 22mm Panel Sounder / Continuous lit lamp IP20 - Code 200-002Flashing Beacon Sounder 12/24v DC - Code 309-5922

Single pump control panels - Delta 1 / Twin pump control panels - Delta 2Delta 1/10 Delta 2/10 7.5Kw 9-12.5 AmpsDelta 1/15 Delta 2/15 11Kw 11-16 AmpsDelta 1/20 Delta 2/20 15Kw 14-20 AmpsIP54 Steel enclosure with interlock main isolator. Line fuses and overload relays. Transformer for low voltage circuit, auto changeover relay (twin pump) run and trip indicators and hour counter, auto off manual switch. Alarm circuit 24v AC.Single pump panels require a two float operation (three if using the alarm feature).Twin pump panels require a three float operation (four if using the alarm feature).Optional Extra's - High Level Alarm Equipment –Rectifier AC-DC & Internal buzzer/Remote connection – Code 200-00112 Volt AC/DC 22mm Panel Sounder / Continuous lit lamp IP20 - Code 200-002Flashing Beacon Sounder 12/24v DC - Code 309-5922

DIVER/MATIC is a portable signalling apparatus, visual and acoustic, for the gauging of the water level in a borehole. DIVER/MATIC is equipped of a metric cable, number by a 0-200 m scale and roll up cable with bracket. For its working and power supply it is enough a standard 9 Vcc pile, included with the device. Thanks to the indelible marked metric numeration on the cable sheath, it is possible to read the distance from the water surface by means of the bipolar probe, which provides to turn on a LED and its relative acoustic signal. Probe Ø 16 mm 120 mm length

Full control panel for single pump 230v comes complete with resetable overload switch, interlock main isolator, line fuses, starters with overload relays and pump run and trip indicators. 24 volt ac supply for audible warning when using third float. Various overloads are available to suit your requirements - 2.3-4amp/6.3-10amp/10-16amp (advise when ordering)Fitted in a IP54 steel enclosure which will protect it from accidental splashes of water.Low voltage 24 volt supply to float switches (not supplied) confirming to water regulations.When using the three float system the top float is the high level alarm float which can operate a audible/visual indicator (optional extra) to alert there is a problem. Full Pump Control PanelAvailable as single pump or twin pump operation230vIP54 EnclosureInterlock Mains IsolatorLine FusesOverload RelaysHour CounterPump Run & Trip IndicatorsSingle pump panelH 400mm x W 300mm x D 160mm 12KgTwin pump panel H 500mm x W 400mm x D 200mm 14.5Kg

Full control panel for twin pumps 415v comes complete with resetable overload switch, interlock main isolator, line fuses, starters with overload relays and pump run and trip indicators. 24 volt ac supply for audible warning when using third float. Various overloads are available to suit your requirements - 2.3-4amp/6.3-10amp/10-16amp (advise when ordering)Fitted in a IP54 steel enclosure which will protect it from accidental splashes of water.Low voltage 24 volt supply to float switches (not supplied) confirming to water regulations.When using the three float system the top float is the high level alarm float which can operate a audible/visual indicator (optional extra) to alert there is a problem. Full Pump Control PanelAvailable as single pump or twin pump operation415vIP54 EnclosureInterlock Mains IsolatorLine FusesOverload RelaysHour CounterPump Run & Trip IndicatorsSingle pump panel H 400mm x W 300mm x D 160mm 12KgTwin pump panel H 500mm x W 400mm x D 200mm 14.5Kg

Full control panel for single pump 230v comes complete with resetable overload switch, interlock main isolator, line fuses, starters with overload relays and pump run and trip indicators. 24 volt ac supply for audible warning when using third float. Various overloads are available to suit your requirements - 2.3-4amp/6.3-10amp/10-16amp (advise when ordering)Fitted in a IP54 steel enclosure which will protect it from accidental splashes of water.Low voltage 24 volt supply to float switches (not supplied) confirming to water regulations.When using the three float system the top float is the high level alarm float which can operate a audible/visual indicator (optional extra) to alert there is a problem. Full Pump Control PanelAvailable as single pump or twin pump operation230vIP54 EnclosureInterlock Mains IsolatorLine FusesOverload RelaysHour CounterPump Run & Trip IndicatorsSingle pump panelH 400mm x W 300mm x D 160mm 12KgTwin pump panel H 500mm x W 400mm x D 200mm 14.5Kg

Full control panel for single pump 415v comes complete with resetable overload switch, interlock main isolator, line fuses, starters with overload relays and pump run and trip indicators. 24 volt ac supply for audible warning when using third float. Various overloads are available to suit your requirements - 2.3-4amp/6.3-10amp/10-16amp (advise when ordering)Fitted in a IP54 steel enclosure which will protect it from accidental splashes of water.Low voltage 24 volt supply to float switches (not supplied) confirming to water regulations.When using the three float system the top float is the high level alarm float which can operate a audible/visual indicator (optional extra) to alert there is a problem. Full Pump Control PanelAvailable as single pump or twin pump operation415vIP54 EnclosureInterlock Mains IsolatorLine FusesOverload RelaysHour CounterPump Run & Trip IndicatorsSingle pump panel H 400mm x W 300mm x D 160mm 12KgTwin pump panel H 500mm x W 400mm x D 200mm 14.5Kg

Guardian ME3.0-7.5Kw10-20 Amp415vGuardians give dry run protection without probes in the wellReplaces the standard control box and monitors power factorCan be wired to pressure switches etcGuardian 2E provides dry run protection without the need for probes in the wellThe control box replaces the standard control box and monitors motor power factor to detect dry running or blocked conditions.If the panel detects a rise or fall in power factor, it cuts power to the motor, it will then allow a cool off period of20, 45, & 90 minute intervals to see if water level has recovered - if not it turns the power off to protect the motor.Replaces existing control box and can be wired to pressure switches

For Installation directly on the pipelineSet Pressure 1.0-7.5 bar230v2.2Kw10 AmpMax Over Pressure 12 barLCD DisplayHydrocontroller have been specifically developed to manage electric pumps both single phase (with permanent capacitor) and three phase. Special attention has been addressed to the User Interface to allow a quick and easy installation. On the front of the device there are 4 buttons and 16 characters 2 line display for managing functioning and alarm parameters. Through the messages displayed there is no need to consult the manual to locate and interpret the parameters. the parameters for the operation are the desired pressure and maximum current of the pump. In the event of an abnormal situation Hydrocontroller protects the pump by switching off, but in order to safeguard the water supply it will undertake repeated automatic or programmed reset attempts. This advanced model has the features to allow groups of up to 8 pumps (all pumps must be identical). In the multi-pumps mode, each pump is controlled and regulated by a Hydrocontroller. In this configuration, the system handles all the pumps used in variable speed, increasing/decreasing together their sped of rotation, in order to keep the pressure constant as the flow rate varies. The alternation of the pumps is guaranteed and, in case of failure of a component the system automatically reconfigures itself. Hydrocontroller wet version has 1 1/4" female threads on the inlet and outlet.

For Installation directly on the pipelineSet Pressure 1.0-7.5 bar230v2.2Kw8 AmpMax Over Pressure 12 barLCD DisplayHydrocontroller have been specifically developed to manage electric pumps both single phase (with permanent capacitor) and three phase. Special attention has been addressed to the User Interface to allow a quick and easy installation. On the front of the device there are 4 buttons and 16 characters 2 line display for managing functioning and alarm parameters. Through the messages displayed there is no need to consult the manual to locate and interpret the parameters. the parameters for the operation are the desired pressure and maximum current of the pump. In the event of an abnormal situation Hydrocontroller protects the pump by switching off, but in order to safeguard the water supply it will undertake repeated automatic or programmed reset attempts. This advanced model has the features to allow groups of up to 8 pumps (all pumps must be identical). In the multi-pumps mode, each pump is controlled and regulated by a Hydrocontroller. In this configuration, the system handles all the pumps used in variable speed, increasing/decreasing together their sped of rotation, in order to keep the pressure constant as the flow rate varies. The alternation of the pumps is guaranteed and, in case of failure of a component the system automatically reconfigures itself. Hydrocontroller wet version has 1 1/4" female threads on the inlet and outlet.

Kiosk Single Door High Impact ployethylene Green Body H)1000mm W)700mm D)450mm Door 900mm x 550mm Interior Backing Board 800mmx500mm Polycarbonate Lock Image shown in green but other colours can be made, just phone and ask.

The Hydrocontroller is used to continuously regluate the rotation speed of elctro pumps, thus ensuring a contante pressure despite varying flow. This unit can be used for water cooling.For Installation directly on the pipelineSet Pressure 1.0-7.5 bar230v2.2Kw8AmpMax Over Pressure 12 barLCD DisplayInput/ Output 11.4" FemaleOutput frequency 60HtzHxLxW mm 360x246x170Weight 2.5kg

MIDA drives are a next generation of on-board motor invertersMounted directly to vertical or horizontal motor terminal plate, allowing direct control of the units via various inputs.Usable in constant pressure, differential pressure, Fixed speed, Flow and temperature control.Programmable via the onboard LCD display, or via the mobile app,Nastec NOWUsable as a stand alone pump, or in COMBO mode for multiple unitsMIDA 20# range operates on 230v single phase input, to provide an output of 3phase/230v.Requiring a 3 phase motor with 230v connection.Mida 40# range operates on 415v 3phase input and output.

MIDA drives are a next generation of on-board motor invertersMounted directly to vertical or horizontal motor terminal plate, allowing direct control of the units via various inputs.Usable in constant pressure, differential pressure, Fixed speed, Flow and temperature control.Programmable via the onboard LCD display, or via the mobile app,Nastec NOWUsable as a stand alone pump, or in COMBO mode for multiple unitsMIDA 20# range operates on 230v single phase input, to provide an output of 3phase/230v.Requiring a 3 phase motor with 230v connection.Mida 40# range operates on 415v 3phase input and output.

MIDA drives are a next generation of on-board motor invertersMounted directly to vertical or horizontal motor terminal plate, allowing direct control of the units via various inputs.Usable in constant pressure, differential pressure, Fixed speed, Flow and temperature control.Programmable via the onboard LCD display, or via the mobile app,Nastec NOWUsable as a stand alone pump, or in COMBO mode for multiple unitsMIDA 20# range operates on 230v single phase input, to provide an output of 3phase/230v.Requiring a 3 phase motor with 230v connection.Mida 40# range operates on 415v 3phase input and output.

MIDA drives are a next generation of on-board motor invertersMounted directly to vertical or horizontal motor terminal plate, allowing direct control of the units via various inputs.Usable in constant pressure, differential pressure, Fixed speed, Flow and temperature control.Programmable via the onboard LCD display, or via the mobile app,Nastec NOWUsable as a stand alone pump, or in COMBO mode for multiple unitsMIDA 20# range operates on 230v single phase input, to provide an output of 3phase/230v.Requiring a 3 phase motor with 230v connection.Mida 40# range operates on 415v 3phase input and output.

The Backlit LCD Displays the running current (amperage) and the power factor (PF) and allows the user to set the values for protection of the pumps.The unit will cut power to the pump if the Maximum amperage is reached (user defined)or if the power factor (PF) drops below the set limit (user defined)This protects against the pump running in overload and also running out of water (Dry run).Pilot is an electronic device for the control of single phase and three phase motors (pumps), which provides protection against;Dry Running.Over current.Power loss.Excessive starts (per hour).COM-N.O-N.C contacts for use with external alarm.2X NO/NC digital inputs.Automatically attempts to restart up to 5 times, after which if problems persist will stop until manually reset.

The Backlit LCD Displays the running current (amperage) and the power factor (PF) and allows the user to set the values for protection of the pumps.The unit will cut power to the pump if the Maximum amperage is reached (user defined)or if the power factor (PF) drops below the set limit (user defined)This protects against the pump running in overload and also running out of water (Dry run).Pilot is an electronic device for the control of single phase and three phase motors (pumps), which provides protection against;Dry Running.Over current.Power loss.Excessive starts (per hour).COM-N.O-N.C contacts for use with external alarm.2X NO/NC digital inputs.Automatically attempts to restart up to 5 times, after which if problems persist will stop until manually reset.

The Backlit LCD Displays the running current (amperage) and the power factor (PF) and allows the user to set the values for protection of the pumps.The unit will cut power to the pump if the Maximum amperage is reached (user defined)or if the power factor (PF) drops below the set limit (user defined)This protects against the pump running in overload and also running out of water (Dry run)

The Backlit LCD Displays the running current (amperage) and the power factor (PF) and allows the user to set the values for protection of the pumps.The unit will cut power to the pump if the Maximum amperage is reached (user defined)or if the power factor (PF) drops below the set limit (user defined)This protects against the pump running in overload and also running out of water (Dry run)

The Backlit LCD Displays the running current (amperage) and the power factor (PF) and allows the user to set the values for protection of the pumps.The unit will cut power to the pump if the Maximum amperage is reached (user defined)or if the power factor (PF) drops below the set limit (user defined)This protects against the pump running in overload and also running out of water (Dry run)

VASCO - Variable Speed Controller units are extremely compact and can connect to almost any pump on the market. They will manage the operation of the pump to maintain a constant desired pressure and flow. The pumping system runs only at the speed necessary to meet the user’s requirements, ensuring energy savings and extending the life of the system.The device also provides motor protection and monitoring such as -Protection against overload and dry running, indication of input current and supply voltage, integrated soft start and soft stop functions extending the life of the system and reducing peak absorption. recording running hours and loggings errors and alarms reported by the system, controlling a second or third pump at constant speed. Connect to other devices to get combined operationThe inverter controls the pump speed to maintain constant pressure at a set point independent of the water demand in the system. In a hydraulic system equipped with inverter, the standard pressure tank is replaced by a smaller tank which functions to maintain the set pressure in the system when the pump is stopped.Vasco variable pump speed drive come complete with motor mounting kit that fits onto the top of the pump motor fan cover - Models V209-V430. Models V438-V448-V465 come complete with side motor mounting kitTransducer model SP16 0-16 Bar, 4-20mA are supplied separately, see code 1000-9590

VASCO - Variable Speed Controller units are extremely compact and can connect to almost any pump on the market. They will manage the operation of the pump to maintain a constant desired pressure and flow. The pumping system runs only at the speed necessary to meet the user’s requirements, ensuring energy savings and extending the life of the system.The device also provides motor protection and monitoring such as -Protection against overload and dry running, indication of input current and supply voltage, integrated soft start and soft stop functions extending the life of the system and reducing peak absorption. recording running hours and loggings errors and alarms reported by the system, controlling a second or third pump at constant speed. Connect to other devices to get combined operationThe inverter controls the pump speed to maintain constant pressure at a set point independent of the water demand in the system. In a hydraulic system equipped with inverter, the standard pressure tank is replaced by a smaller tank which functions to maintain the set pressure in the system when the pump is stopped.Vasco variable pump speed drive come complete with motor mounting kit that fits onto the top of the pump motor fan cover - Models V209-V430. Models V438-V448-V465 come complete with side motor mounting kitTransducer model SP16 0-16 Bar, 4-20mA are supplied separately, see code 1000-9590

VASCO - Variable Speed Controller units are extremely compact and can connect to almost any pump on the market. They will manage the operation of the pump to maintain a constant desired pressure and flow. The pumping system runs only at the speed necessary to meet the user’s requirements, ensuring energy savings and extending the life of the system.The device also provides motor protection and monitoring such as -Protection against overload and dry running, indication of input current and supply voltage, integrated soft start and soft stop functions extending the life of the system and reducing peak absorption. recording running hours and loggings errors and alarms reported by the system, controlling a second or third pump at constant speed. Connect to other devices to get combined operationThe inverter controls the pump speed to maintain constant pressure at a set point independent of the water demand in the system. In a hydraulic system equipped with inverter, the standard pressure tank is replaced by a smaller tank which functions to maintain the set pressure in the system when the pump is stopped.Vasco variable pump speed drive come complete with motor mounting kit that fits onto the top of the pump motor fan cover - Models V209-V430. Models V438-V448-V465 come complete with side motor mounting kitTransducer model SP16 0-16 Bar, 4-20mA are supplied separately, see code 1000-9590

VASCO - Variable Speed Controller units are extremely compact and can connect to almost any pump on the market. They will manage the operation of the pump to maintain a constant desired pressure and flow. The pumping system runs only at the speed necessary to meet the user’s requirements, ensuring energy savings and extending the life of the system.The device also provides motor protection and monitoring such as -Protection against overload and dry running, indication of input current and supply voltage, integrated soft start and soft stop functions extending the life of the system and reducing peak absorption. recording running hours and loggings errors and alarms reported by the system, controlling a second or third pump at constant speed. Connect to other devices to get combined operationThe inverter controls the pump speed to maintain constant pressure at a set point independent of the water demand in the system. In a hydraulic system equipped with inverter, the standard pressure tank is replaced by a smaller tank which functions to maintain the set pressure in the system when the pump is stopped.Vasco variable pump speed drive come complete with motor mounting kit that fits onto the top of the pump motor fan cover - Models V209-V430. Models V438-V448-V465 come complete with side motor mounting kitTransducer model SP16 0-16 Bar, 4-20mA are supplied separately, see code 1000-9590

VASCO - Variable Speed Controller units are extremely compact and can connect to almost any pump on the market. They will manage the operation of the pump to maintain a constant desired pressure and flow. The pumping system runs only at the speed necessary to meet the user’s requirements, ensuring energy savings and extending the life of the system.The device also provides motor protection and monitoring such as -Protection against overload and dry running, indication of input current and supply voltage, integrated soft start and soft stop functions extending the life of the system and reducing peak absorption. recording running hours and loggings errors and alarms reported by the system, controlling a second or third pump at constant speed. Connect to other devices to get combined operationThe inverter controls the pump speed to maintain constant pressure at a set point independent of the water demand in the system. In a hydraulic system equipped with inverter, the standard pressure tank is replaced by a smaller tank which functions to maintain the set pressure in the system when the pump is stopped.Vasco variable pump speed drive come complete with motor mounting kit that fits onto the top of the pump motor fan cover - Models V209-V430. Models V438-V448-V465 come complete with side motor mounting kitTransducer model SP16 0-16 Bar, 4-20mA are supplied separately, see code 1000-9590

VASCO - Variable Speed Controller units are extremely compact and can connect to almost any pump on the market. They will manage the operation of the pump to maintain a constant desired pressure and flow. The pumping system runs only at the speed necessary to meet the user’s requirements, ensuring energy savings and extending the life of the system.The device also provides motor protection and monitoring such as -Protection against overload and dry running, indication of input current and supply voltage, integrated soft start and soft stop functions extending the life of the system and reducing peak absorption. recording running hours and loggings errors and alarms reported by the system, controlling a second or third pump at constant speed. Connect to other devices to get combined operationThe inverter controls the pump speed to maintain constant pressure at a set point independent of the water demand in the system. In a hydraulic system equipped with inverter, the standard pressure tank is replaced by a smaller tank which functions to maintain the set pressure in the system when the pump is stopped.Vasco variable pump speed drive come complete with motor mounting kit that fits onto the top of the pump motor fan cover - Models V209-V430. Models V438-V448-V465 come complete with side motor mounting kitTransducer model SP16 0-16 Bar, 4-20mA are supplied separately, see code 1000-9590

VASCO - Variable Speed Controller units are extremely compact and can connect to almost any pump on the market. They will manage the operation of the pump to maintain a constant desired pressure and flow. The pumping system runs only at the speed necessary to meet the user’s requirements, ensuring energy savings and extending the life of the system.The device also provides motor protection and monitoring such as -Protection against overload and dry running, indication of input current and supply voltage, integrated soft start and soft stop functions extending the life of the system and reducing peak absorption. recording running hours and loggings errors and alarms reported by the system, controlling a second or third pump at constant speed. Connect to other devices to get combined operationThe inverter controls the pump speed to maintain constant pressure at a set point independent of the water demand in the system. In a hydraulic system equipped with inverter, the standard pressure tank is replaced by a smaller tank which functions to maintain the set pressure in the system when the pump is stopped.Vasco variable pump speed drive come complete with motor mounting kit that fits onto the top of the pump motor fan cover - Models V209-V430. Models V438-V448-V465 come complete with side motor mounting kitTransducer model SP16 0-16 Bar, 4-20mA are supplied separately, see code 1000-9590

VASCO - Variable Speed Controller units are extremely compact and can connect to almost any pump on the market. They will manage the operation of the pump to maintain a constant desired pressure and flow. The pumping system runs only at the speed necessary to meet the user’s requirements, ensuring energy savings and extending the life of the system.The device also provides motor protection and monitoring such as -Protection against overload and dry running, indication of input current and supply voltage, integrated soft start and soft stop functions extending the life of the system and reducing peak absorption. recording running hours and loggings errors and alarms reported by the system, controlling a second or third pump at constant speed. Connect to other devices to get combined operationThe inverter controls the pump speed to maintain constant pressure at a set point independent of the water demand in the system. In a hydraulic system equipped with inverter, the standard pressure tank is replaced by a smaller tank which functions to maintain the set pressure in the system when the pump is stopped.Vasco variable pump speed drive come complete with motor mounting kit that fits onto the top of the pump motor fan cover - Models V209-V430. Models V438-V448-V465 come complete with side motor mounting kitTransducer model SP16 0-16 Bar, 4-20mA are supplied separately, see code 1000-9590

VASCO - Variable Speed Controller units are extremely compact and can connect to almost any pump on the market. They will manage the operation of the pump to maintain a constant desired pressure and flow. The pumping system runs only at the speed necessary to meet the user’s requirements, ensuring energy savings and extending the life of the system.The device also provides motor protection and monitoring such as -Protection against overload and dry running, indication of input current and supply voltage, integrated soft start and soft stop functions extending the life of the system and reducing peak absorption. recording running hours and loggings errors and alarms reported by the system, controlling a second or third pump at constant speed. Connect to other devices to get combined operationThe inverter controls the pump speed to maintain constant pressure at a set point independent of the water demand in the system. In a hydraulic system equipped with inverter, the standard pressure tank is replaced by a smaller tank which functions to maintain the set pressure in the system when the pump is stopped.Vasco variable pump speed drive come complete with motor mounting kit that fits onto the top of the pump motor fan cover - Models V209-V430. Models V438-V448-V465 come complete with side motor mounting kitTransducer model SP16 0-16 Bar, 4-20mA are supplied separately, see code 1000-9590

VASCO - Variable Speed Controller units are extremely compact and can connect to almost any pump on the market. They will manage the operation of the pump to maintain a constant desired pressure and flow. The pumping system runs only at the speed necessary to meet the user’s requirements, ensuring energy savings and extending the life of the system.The device also provides motor protection and monitoring such as -Protection against overload and dry running, indication of input current and supply voltage, integrated soft start and soft stop functions extending the life of the system and reducing peak absorption. recording running hours and loggings errors and alarms reported by the system, controlling a second or third pump at constant speed. Connect to other devices to get combined operationThe inverter controls the pump speed to maintain constant pressure at a set point independent of the water demand in the system. In a hydraulic system equipped with inverter, the standard pressure tank is replaced by a smaller tank which functions to maintain the set pressure in the system when the pump is stopped.Vasco variable pump speed drive come complete with motor mounting kit that fits onto the top of the pump motor fan cover - Models V209-V430. Models V438-V448-V465 come complete with side motor mounting kitTransducer model SP16 0-16 Bar, 4-20mA are supplied separately, see code 1000-9590

VASCO - Variable Speed Controller units are extremely compact and can connect to almost any pump on the market. They will manage the operation of the pump to maintain a constant desired pressure and flow. The pumping system runs only at the speed necessary to meet the user’s requirements, ensuring energy savings and extending the life of the system.The device also provides motor protection and monitoring such as -Protection against overload and dry running, indication of input current and supply voltage, integrated soft start and soft stop functions extending the life of the system and reducing peak absorption. recording running hours and loggings errors and alarms reported by the system, controlling a second or third pump at constant speed. Connect to other devices to get combined operationThe inverter controls the pump speed to maintain constant pressure at a set point independent of the water demand in the system. In a hydraulic system equipped with inverter, the standard pressure tank is replaced by a smaller tank which functions to maintain the set pressure in the system when the pump is stopped.Vasco variable pump speed drive come complete with motor mounting kit that fits onto the top of the pump motor fan cover - Models V209-V430. Models V438-V448-V465 come complete with side motor mounting kitTransducer model SP16 0-16 Bar, 4-20mA are supplied separately, see code 1000-9590

The 230v Presscontrol is a electronic pressure switch and protection device.Can be fitted to almost any pump with an outlet pressure of two bar minimum to ten bar maximum with a flow rate of between 40-200 litres per min. The presscontrol will turn off in the case of no water to protect the pump from dry running.The 110v Presscontrol is a electronic pressure switch and protection device.Can be fitted to almost any pump with an outlet pressure of two bar minimum to ten bar maximum with a flow rate of between 40-200 litres per min. The presscontrol will turn off in the case of no water to protect the pump from dry running.Suitable for most water systems from well, tank or low pressure mains.Anotherversion called the controlpress is available for pumps with larger motors to be installed.Presscontrol110 Volt1.5Kw Maximum8 Amp Maximum1" Male BSP Inlet/Outlet1.4KgAutomatically turns on and off a pump

The 230v Fuel Presscontrol is a electronic pressure switch and protection device.Can be fitted to almost any fuel oil pump with an outlet pressure of two bar minimum to ten bar maximum with a flow rate of between 40-200 litres per miN.The fuel oil presscontrol will turn off in the case of no fluid to protect the pump from dry running.Fuel Presscontrol230 Volt1.5Kw Maximum8 Amp Maximum1" Male BSP Inlet/Outlet1.4KgAutomatically turns on and off a pump

The 230v Presscontrol is a electronic pressure switch and protection device.Can be fitted to almost any pump with an outlet pressure of two bar minimum to ten bar maximum with a flow rate of between 40-200 litres per min. The presscontrol will turn off in the case of no water to protect the pump from dry running.Suitable for most water systems from well, tank or low pressure mains.Another version called the controlpress is available for pumps with larger motors to be installed.Presscontrol230 Volt1.5Kw Maximum8 Amp Maximum1" Male BSP Inlet/Outlet1.4KgAutomatically turns on and off a pump

The 230v Fuel Oil Presscontrol is a electronic pressure switch and protection deviceCan be fitted to almost any fuel oil pump with an outlet pressure of two bar minimum to ten bar maximum with a flow rate of between 40-200 litres per minThe fuel oil presscontrol will turn off in the case of no fluidto protect the pump from dry running.Fuel Oil Presscontrol230 Volt1.5Kw Maximum8 Amp Maximum1" Male BSP Inlet/Outlet1.4KgAutomatically turns on and off a pump

Puddle SensorFor Use withUtility 1510m Cable5 Wire

Simplex Duplex UP M/3 Basic Twin Pump Control Panel 400v.Simplex control panels for one pump control of sump pumps, booster pumps or borehole pump. Operation by floats, pressure switches or level probes.Duplex control panels for two pump control of sump pumps or booster pumps. Operation by floats or pressure switches.Both have provision for klixon connections and a 12 Volt DC Alarm control circuit. Plastic ABS boxes and IP55 Rated.Optional Extra's - High Level Alarm Equipment -12 Volt AC/DC 22mm Panel Sounder / Continuous lit lamp IP20 - Code 200-002Flashing Beacon Sounder 12/24v DC - Code309-5922

Simplex Duplex UP T/10 Basic Twin Pump Control Panel 400v.Simplex Duplex control panels for one pump control of sump pumps, booster pumps or borehole pump. Operation by floats, pressure switches or level probes.Duplex control panels for two pump control of sump pumps or booster pumps. Operation by floats or pressure switches.Both have provision for klixon connections and a 12 Volt DC Alarm control circuit. Plastic ABS boxes and IP55 Rated.Optional Extra's - High Level Alarm Equipment -12 Volt AC/DC 22mm Panel Sounder / Continuous lit lamp IP20 - Code 200-002Flashing Beacon Sounder 12/24v DC - Code309-5922

These IP50 enclosure control panels offer single pump control with manual (non latching) and automatic operation with overload protection. Pumps with external capacitors can be fitted within the enclosures. These can be used for single or twn float operation, pressure switch operation and/or probe operation. Two way operation of either emptying or filling. Please take a look at our range of float switches also found our site.QA/50B 110vSingle pump control panelHxWxL 220 x 255 x 130 mmVoltage 100vAmp Range 2-18Kw Range 0.37-2.2Ask us about other sizes and types

These IP50 enclosure control panels offer single pump control with manual (non latching) and automatic operation with overload protection. Pumps with external capacitors can be fitted within the enclosures. These can be used for single or twn float operation, pressure switch operation and/or probe operation. Two way operation of either emptying or filling. Please take a look at our range of float switches also found our site.QA/50BSingle pump control panelHxWxL 220 x 255 x 130 mmVoltage 230vAmp Range 2-18Kw Range 0.37-2.2Ask us about other sizes and types

Simplex UP T/10 Basic Single Pump Control Panel 400v.These IP50 enclosure control panels offer single pump control with manual (non latching) and automatic operation with overload protection. Pumps with external capacitors can be fitted within the enclosures. These can be used for single or twn float operation, pressure switch operation and/or probe operation. Two way operation of either emptying or filling. Please take a look at our range of float switches also found our site.QA/50B 400vSingle pump control panelHxWxL 220 x 255 x 130 mmVoltage 400vAmp Range 2-18Kw Range 0.37-2.2Ask us about other sizes and types

Simplex UP T/15 Basic Single Pump Control Panel 400v.Simplex control panels for one pump control of sump pumps, booster pumps or borehole pump. Operation by floats, pressure switches or level probes.Duplex control panels for two pump control of sump pumps or booster pumps. Operation by floats or pressure switches.Both have provision for klixon connections and a 12 Volt DC Alarm control circuit. Plastic ABS boxes and IP55 Rated.Optional Extra's - High Level Alarm Equipment -12 Volt AC/DC 22mm Panel Sounder / Continuous lit lamp IP20 - Code 200-002Flashing Beacon Sounder 12/24v DC - Code309-5922

Triple 3 pump full control panels available for 3 x 230v pumps or 3 x 400v pumps.Complete interlock main isolator, line fuses,pump run and trip indicators. (Hour counters on 230v only)12 volt ac supply for audible warning when using high level featureFitted in a IP54 steel enclosure which will protect it from accidental splashes of waterLow voltage 12 volt supply to float switches (not supplied) confirming to water regulations. When using the four or five float system the top float is the high level alarm float which can operate a audible/visual indicator (optional extra) to alert there is a problemCall us for stock availabilityOptional Extra's - High Level Alarm Equipment –12 Volt AC/DC 22mm Panel Sounder / Continuous lit lamp IP20 - Code 200-002Flashing Beacon Sounder 12/24v DC - Code309-5922

Triple 3 pump full control panels available for 3 x 230v pumps or 3 x 400v pumps.Complete interlock main isolator, line fuses,pump run and trip indicators. (Hour counters on 230v only)12 volt ac supply for audible warning when using high level featureFitted in a IP54 steel enclosure which will protect it from accidental splashes of waterLow voltage 12 volt supply to float switches (not supplied) confirming to water regulations. When using the four or five float system the top float is the high level alarm float which can operate a audible/visual indicator (optional extra) to alert there is a problemCall us for stock availabilityOptional Extra's - High Level Alarm Equipment –12 Volt AC/DC 22mm Panel Sounder / Continuous lit lamp IP20 - Code 200-002Flashing Beacon Sounder 12/24v DC - Code 309-5922

Utility Panel 15-13-13 AmpPerfect for use with Puddle SensorFor use with all residue pumps, PXL, RSD400 etc

Easy to install, VSD manages all controls necessary for a pumping system. VSD variable speed pumping system keeps constant delivery when pressure variations occur. The status display allows instant overview of operating characteristics. VSD cuts your electricity usage by automatically pumping only what is required by the system. All units require pressure accumulator vessels – see page 77 of the PDF attachment. The display indicates: Pump working frequency, Instant pressure, Absorbed power, Alarms.

Easy to install, VSD manages all controls necessary for a pumping system. VSD variable speed pumping system keeps constant delivery when pressure variations occur. The status display allows instant overview of operating characteristics. VSD cuts your electricity usage by automatically pumping only what is required by the system. All units require pressure accumulator vessels – see page 77 of the PDF attachment. The display indicates: Pump working frequency, Instant pressure, Absorbed power, Alarm.

Easy to install, VSD manages all controls necessary for a pumping system. VSD variable speed pumping system keeps constant delivery when pressure variations occur. The status display allows instant overview of operating characteristics. VSD cuts your electricity usage by automatically pumping only what is required by the system. All units require pressure accumulator vessels – see page 77 of the PDF attachment. The display indicates: Pump working frequency, Instant pressure, Absorbed power, Alarm.

Easy to install, VSD manages all controls necessary for a pumping system.VSD variable speed pumping system keeps constant delivery when pressure variations occur. The status display allows instant overview of operating characteristics.VSD cuts your electricity usage by automatically pumping only what is required by the system. All units require pressure accumulator vessels – see page 77 of the PDF attachment. The display indicates: Pump working frequency, Instant pressure, Absorbed power , Alarms.