Control panels

DIVER/MATIC is a portable signalling apparatus, visual and acoustic, for the gauging of the water level in a borehole. DIVER/MATIC is equipped of a metric cable, number by a 0-200 m scale and roll up cable with bracket. For its working and power supply it is enough a standard 9 Vcc pile, included with the device. Thanks to the indelible marked metric numeration on the cable sheath, it is possible to read the distance from the water surface by means of the bipolar probe, which provides to turn on a LED and its relative acoustic signal. Probe Ø 16 mm 120 mm length

Full control panel for single pump 230v comes complete with resetable overload switch, interlock main isolator, line fuses, starters with overload relays and pump run and trip indicators. 24 volt ac supply for audible warning when using third float. Various overloads are available to suit your requirements - 2.3-4amp/6.3-10amp/10-16amp (advise when ordering)Fitted in a IP54 steel enclosure which will protect it from accidental splashes of water.Low voltage 24 volt supply to float switches (not supplied) confirming to water regulations.When using the three float system the top float is the high level alarm float which can operate a audible/visual indicator (optional extra) to alert there is a problem. Full Pump Control PanelAvailable as single pump or twin pump operation230vIP54 EnclosureInterlock Mains IsolatorLine FusesOverload RelaysHour CounterPump Run & Trip IndicatorsSingle pump panelH 400mm x W 300mm x D 160mm 12KgTwin pump panel H 500mm x W 400mm x D 200mm 14.5Kg

Full control panel for twin pumps 415v comes complete with resetable overload switch, interlock main isolator, line fuses, starters with overload relays and pump run and trip indicators. 24 volt ac supply for audible warning when using third float. Various overloads are available to suit your requirements - 2.3-4amp/6.3-10amp/10-16amp (advise when ordering)Fitted in a IP54 steel enclosure which will protect it from accidental splashes of water.Low voltage 24 volt supply to float switches (not supplied) confirming to water regulations.When using the three float system the top float is the high level alarm float which can operate a audible/visual indicator (optional extra) to alert there is a problem. Full Pump Control PanelAvailable as single pump or twin pump operation415vIP54 EnclosureInterlock Mains IsolatorLine FusesOverload RelaysHour CounterPump Run & Trip IndicatorsSingle pump panel H 400mm x W 300mm x D 160mm 12KgTwin pump panel H 500mm x W 400mm x D 200mm 14.5Kg

Full control panel for single pump 230v comes complete with resetable overload switch, interlock main isolator, line fuses, starters with overload relays and pump run and trip indicators. 24 volt ac supply for audible warning when using third float. Various overloads are available to suit your requirements - 2.3-4amp/6.3-10amp/10-16amp (advise when ordering)Fitted in a IP54 steel enclosure which will protect it from accidental splashes of water.Low voltage 24 volt supply to float switches (not supplied) confirming to water regulations.When using the three float system the top float is the high level alarm float which can operate a audible/visual indicator (optional extra) to alert there is a problem. Full Pump Control PanelAvailable as single pump or twin pump operation230vIP54 EnclosureInterlock Mains IsolatorLine FusesOverload RelaysHour CounterPump Run & Trip IndicatorsSingle pump panelH 400mm x W 300mm x D 160mm 12KgTwin pump panel H 500mm x W 400mm x D 200mm 14.5Kg

Full control panel for single pump 415v comes complete with resetable overload switch, interlock main isolator, line fuses, starters with overload relays and pump run and trip indicators. 24 volt ac supply for audible warning when using third float. Various overloads are available to suit your requirements - 2.3-4amp/6.3-10amp/10-16amp (advise when ordering)Fitted in a IP54 steel enclosure which will protect it from accidental splashes of water.Low voltage 24 volt supply to float switches (not supplied) confirming to water regulations.When using the three float system the top float is the high level alarm float which can operate a audible/visual indicator (optional extra) to alert there is a problem. Full Pump Control PanelAvailable as single pump or twin pump operation415vIP54 EnclosureInterlock Mains IsolatorLine FusesOverload RelaysHour CounterPump Run & Trip IndicatorsSingle pump panel H 400mm x W 300mm x D 160mm 12KgTwin pump panel H 500mm x W 400mm x D 200mm 14.5Kg

Guardian ME3.0-7.5Kw10-20 Amp415vGuardians give dry run protection without probes in the wellReplaces the standard control box and monitors power factorCan be wired to pressure switches etcGuardian 2E provides dry run protection without the need for probes in the wellThe control box replaces the standard control box and monitors motor power factor to detect dry running or blocked conditions.If the panel detects a rise or fall in power factor, it cuts power to the motor, it will then allow a cool off period of20, 45, & 90 minute intervals to see if water level has recovered - if not it turns the power off to protect the motor.Replaces existing control box and can be wired to pressure switches

For Installation directly on the pipelineSet Pressure 1.0-7.5 bar230v2.2Kw10 AmpMax Over Pressure 12 barLCD DisplayHydrocontroller have been specifically developed to manage electric pumps both single phase (with permanent capacitor) and three phase. Special attention has been addressed to the User Interface to allow a quick and easy installation. On the front of the device there are 4 buttons and 16 characters 2 line display for managing functioning and alarm parameters. Through the messages displayed there is no need to consult the manual to locate and interpret the parameters. the parameters for the operation are the desired pressure and maximum current of the pump. In the event of an abnormal situation Hydrocontroller protects the pump by switching off, but in order to safeguard the water supply it will undertake repeated automatic or programmed reset attempts. This advanced model has the features to allow groups of up to 8 pumps (all pumps must be identical). In the multi-pumps mode, each pump is controlled and regulated by a Hydrocontroller. In this configuration, the system handles all the pumps used in variable speed, increasing/decreasing together their sped of rotation, in order to keep the pressure constant as the flow rate varies. The alternation of the pumps is guaranteed and, in case of failure of a component the system automatically reconfigures itself. Hydrocontroller wet version has 1 1/4" female threads on the inlet and outlet.

For Installation directly on the pipelineSet Pressure 1.0-7.5 bar230v2.2Kw8 AmpMax Over Pressure 12 barLCD DisplayHydrocontroller have been specifically developed to manage electric pumps both single phase (with permanent capacitor) and three phase. Special attention has been addressed to the User Interface to allow a quick and easy installation. On the front of the device there are 4 buttons and 16 characters 2 line display for managing functioning and alarm parameters. Through the messages displayed there is no need to consult the manual to locate and interpret the parameters. the parameters for the operation are the desired pressure and maximum current of the pump. In the event of an abnormal situation Hydrocontroller protects the pump by switching off, but in order to safeguard the water supply it will undertake repeated automatic or programmed reset attempts. This advanced model has the features to allow groups of up to 8 pumps (all pumps must be identical). In the multi-pumps mode, each pump is controlled and regulated by a Hydrocontroller. In this configuration, the system handles all the pumps used in variable speed, increasing/decreasing together their sped of rotation, in order to keep the pressure constant as the flow rate varies. The alternation of the pumps is guaranteed and, in case of failure of a component the system automatically reconfigures itself. Hydrocontroller wet version has 1 1/4" female threads on the inlet and outlet.