Air Driven Pumps

This air operated submersible pump, also known as a pneumatic submersible pump, is traditionally used in mining and construction industries for many applications, such as dewatering and sump drainage.Will pump down to 22 mmHandles solids up to 3 mmGovernor controlled motorCompact design enables use in restricted areas

Portable ARO / Ingersoll Rand extrusion system with a 2 ball, 4 ¼" Air Motor 9:1 ratio pump, follower plate and lifting assembly, fitted with PTFE Teflon internal elastomers. A fantastically versatile unit.ARO Piston Pump applications are ideal for viscous and high density fluid where materials are hard to move and dispense. These systems are widely used in garage for grease and lubrication dispensing to point at, around or nearby motor vehicles, but can be adapted to pump almost any given liquid out of a barrel!The pump can be accessorised with multiple follower plates for different usage of barrel size, and we have even been known to adapt the units for higher lift capabilities for larger barrels!These are a highly versatile unit and can make an employees life a lot more efficient when the pump can be taken to the job, instead of to-ing and fro-ing between work stations for multiple tasks!

Halfinch Ingersoll Rand / ARO aluminium diaphragm pump drum package with hytel diaphragms. Designed for 55 gallon barrel duties.FeaturesPerfect for removingyour chemical from any 55-gallon drum.ARO Drum Pumps are available in Aluminum, Stainless Steel or Polypropylene body materials!Stall-Free Operation- ARO Diaphragm Drum Pumps feature a patented "Unbalanced" air valve design that avoids stall-out, even under low air-inlet pressures.Bolted Construction- Unlike traditional band-clamp style pumps, ARO Diaphragm Drum Pumps utilize bolted fasteners for leak-tight integrity.Factory-Matched- ARO Drum Pump Package components (adapters, siphon tubes, etc.) contain pre-specified, matching materials of construction for complete fluid compatibility.Motor-Driven Drum Pumps; Type: Drum; GPM: 11.00; Motor Type: Air; Fluid Inlet Size: 1/2 NPTF; Fluid Outlet Size: 1/2 NPTF; Air Inlet Size: 1/4 NPTF

Motor-Driven Drum Pumps; Type: Drum; GPM: 11.00; Motor Type: Air; Fluid Inlet Size: 1/2 NPTF; Fluid Outlet Size: 1/2 NPTF; Air Inlet Size: 1/4 NPTF

Chicago Pneumatic CP 0010 Submersible Centrifugal PumpsFeatures & Benefits:Single-stage centrifugal units driven by powerful vane motorsDouble seals protect bearings and motor from water and mudIntegral oiler provides continuous lubricationIntegral strainer, air inlet valveBronze impellerCast-iron housingSpecifications:Part Number: T022224Net Weight: 33 Lbs.Water outlet: 50mmMin water depth: 22mmAir consumption: 47 l/sOverall diameter: 8.26" x 9"3 HP1" Air Inlet

COPPUS®Marine Ventilators,Steam-, Air- and Water Turbine-Drive VentilatorsCOPPUS marine ventilators are rugged, dependable cargo tank ventilators that have served the shipping industry for many years. They are ideal for on-board gas-freeing, drying and ventilation operations and are available in supply or exhaust models.Steam / Compressed Air Turbine Drive ModelsC-12A Supply: Delivers 5,350 cfm (9,090 m3/hr)C-12A Exhaust: Delivers 4,600 cfm (7,815 m3/hr)C-15A Supply: Delivers 8,400 cfm (14,275 m3/hr)C-15A Exhaust: Delivers 6,500 cfm (11,040 m3/hr)FeaturesCast iron turbine housing with aluminum coverBronze turbine wheel / stainless steel turbine blades / nozzlesSpark-resistant cast aluminum fan and fan housingStainless steel fasteners, studs and protective screen

Coppus model 3-HP Venturi 8" (203mm).High-Performance, Highly-Efficient Venturi Air MoversThe unmatched performance of the COPPUS Jectair HP is recognized throughout the industry. When compared with older-style air horns, the patented air mixing chamber of the Jectair HP produces up to 26 percent savings on compressed air consumption (see efficiency performance charts).Operating PrincipleCompressed air or steam is admitted to the Jectair through a single inlet connection in the housing leading to the mixing chamber. The air or steam jetted from the nozzle creates a Venturi action which induces a large volume of surrounding air to enter the Jectair through the aerodynamic inlet bell. The air is then discharged at high velocity through the horn-shaped diffuser. NOTE: Operating efficiency depends on compressed air volume and pressure (see performance/efficiency charts).FeaturesAvailable in five sizes: 9, 8, 6-HP, 3-HP, 3S-HPHigh-Performance (HP) and Hornet models available in three sizes: 6-HP, 3-HP and 3-HPAir flows range from 1,370 to 8,900 cfm (2,328 to 15,121m3/hr)Induction ratios up to 40:1Multiple expansion nozzles machined into housingHigh static pressure capabilitiesDiffuser material available in steel, aluminum or shock-resistant polymer (Hornet HP)No moving parts — virtually maintenance-freeStatic bonding cable with spring tension grip and replaceable contact tips standard on all modelsAccepts flexible duct on diffuser end (optional duct adapter for inlet end available)Tripod for stationary mounting available

Coppus model 3S-HP Venturi 8" (203mm).High-Performance, Highly-Efficient Venturi Air MoversThe unmatched performance of the COPPUS Jectair HP is recognized throughout the industry. When compared with older-style air horns, the patented air mixing chamber of the Jectair HP produces up to 26 percent savings on compressed air consumption (see efficiency performance charts). Operating Principle Compressed air or steam is admitted to the Jectair through a single inlet connection in the housing leading to the mixing chamber. The air or steam jetted from the nozzle creates a Venturi action which induces a large volume of surrounding air to enter the Jectair through the aerodynamic inlet bell. The air is then discharged at high velocity through the horn-shaped diffuser. NOTE: Operating efficiency depends on compressed air volume and pressure (see performance/efficiency charts).FeaturesAvailable in five sizes: 9, 8, 6-HP, 3-HP, 3S-HPHigh-Performance (HP) and Hornet models available in three sizes: 6-HP, 3-HP and 3S-HPAir flows range from 1,370 to 8,900 cfm (2,328 to 15,121m3/hr) Induction ratios up to 40:1Multiple expansion nozzles machined into housing. High static pressure capabilitiesDiffuser material available in steel, aluminum or shock-resistant polymer (Hornet HP) No moving parts — virtually maintenance-freeStatic bonding cable with spring tension grip and replaceable contact tips standard on all models. Accepts flexible duct on diffuser end (optional duct adapter for inlet end available) Tripod for stationary mounting available